Search Results

To achieve high robustness and quality, automotive ECUs must initialize from low-power states as quickly as possible. However, microprocessor and memory advances have failed to keep pace with software image size growth in complex ECUs such as in Infotainment and Telematics. Loading the boot image from non-volatile storage to RAM and initializing the software can take a very long time to show the first screen and result in sluggish performance for a significant time thereafter which both degrade customer perceived quality. Designers of mobile devices such as portable phones, laptops, and tablets address this problem using Suspend mode whereby the main processor and peripheral devices are powered down during periods of inactivity, but memory contents are preserved by a small “self-refresh” current. When the device is turned back “on”, fully initialized memory content allows the system to initialize nearly instantaneously.

Understanding customer expectations is critical to satisfying customers. Holding customer clinics is one approach to set winning targets for the engineering functional measures to drive customer satisfaction. In these clinics, customers are asked to operate and interact with vehicle systems or subsystems such as doors, lift gates, shifters, and seat adjusters, and then rate their experience. From this customer evaluation data, engineers can create customer loss or preference functions. These functions let engineers set appropriate targets by balancing risks and benefits. Statistical methods such as cumulative customer loss function are regularly applied for such analyses. In this paper, a new approach based on the Taguchi method is proposed and developed. It is referred to as Taguchi Customer Loss Function (TCLF).

The maximum equivalent plastic strain (EPSmax), which can be achieved in the gauge region of a cruciform specimen during in-plane biaxial tensile tests, is limited due to early fracture on the cruciform specimen arm. In this paper, a theoretical model was proposed to determine the factors related to the EPSmax of a cruciform specimen following ISO 16842: 2014. Biaxial tensile tests were carried out to verify the theoretical analyses. Results show that the material strength coefficient (k) has no effect on the EPSmax, and EPSmax increases with the increase of the material hardening exponent (n) and the cross-sectional-area ratio (c) of the arm region to the gauge region. It is found that the applied load ratio (α) has an effect on EPSmax, which decreases as the load ratio increases from 0:1 (i.e. uniaxial tension) to 1:2 (i.e. plane strain state) and then increases as the load ratio increases to 1:1 (i.e. balanced biaxial tension).

In today's competitive market, noise and vibration are among the most important parameters that impact the success of a vehicle. In body-on-frame construction vehicles, elastomeric body mounts play a major role in isolating the passenger compartment from road noise, harshness, shake, and other vibrations in the chassis as well as improving ride quality across a wide frequency range. This paper describes the work carried out to design a fluid filled mount with high lateral stiffness that can alter the perceived Noise, Vibration and Harshness (NVH) performance of current production body-on-frame trucks. It was found that the quietness and ride qualities can be significantly improved by positioning the glycol-filled mounts at the anti-node of the frame first vertical bending mode; under the C-pillar intersection with the frame. The performance of mounts in this area is known to be critical to ride quality.

The main objective of crash sensing is to predict a vehicle collision early in the event and command vehicle’s occupant protection systems to take appropriate actions to reduce the severity of crash injury. Currently Computer Aided Engineering (CAE) models are being used to predict the sensing signals with sensors placed at front end structure of the vehicle. The front-end structure as well as other critical components packaged in the front end play important role in absorbing energy and provide sensing signals during impact, headlamp being one such critical components. The headlamp with its lens being the exterior surface, experience large magnitude of loads from barrier during full frontal, angled and offset impact. The impact with barrier usually results in scattered damage to the headlamp and its lens. In this paper, CAE model of headlamp has been improved to reflect similar deformation pattern as observed in physical tests.

A primary goal of large eddy simulation, LES, is to capture in-cylinder cycle-to-cycle variability, CCV. This is a first step to assess the efficacy of 35 consecutive computed motored cycles to capture the kinetic energy in the TCC-III engine. This includes both the intra-cycle production and dissipation as well as the kinetic energy CCV. The approach is to sample and compare the simulated three-dimensional velocity equivalently to the available two-component two-dimensional PIV velocity measurements. The volume-averaged scale-resolved kinetic energy from the LES is sampled in three slabs, which are volumes equal to the two axial and one azimuthal PIV fields-of-view and laser sheet thickness. Prior to the comparison, the effects of sampling a cutting plane versus a slab and slabs of different thicknesses are assessed. The effects of sampling only two components and three discrete planar regions is assessed.

Fuel chemistry plays a crucial role in the continued reduction of particulate emissions (PE) and cleaner air quality from vehicles and equipment powered by internal combustion engines (ICE). Over the past ten years, there have been great improvements in predictive particulate emissions indices (correlative mathematical models) based on the fuel’s composition. Examples of these particulate indices (PI) are the Honda Particulate Matter Index (PMI) and the General Motors Particulate Evaluation Index (PEI). However, the analytical chemistry lab methods used to generate data for these two PI indices are very time-consuming. Because gasoline can be mixtures of hundreds of hydrocarbon compounds, these lab methods typically include the use of the high resolution chromatographic separation techniques such as detailed hydrocarbon analysis (DHA), with 100m chromatography columns and long (3 - 4 hours) analysis times per sample.

As passenger vehicle design evolves and accelerates, the use of multi-body dynamics solvers has proven to be invaluable in the engineering workflow. MBD solvers allow engineers to build virtual vehicle models that can accurately simulate vehicle responses and calculate internal forces, which previously could only be assessed using physical prototype builds with hundreds of measurement transducers. Evaluation and selection of solvers within an engineering environment is inherently a multi-dimensional activity that can include ease of use, retention of previously developed expertise, accuracy, speed, and integration with existing analysis processes. We discuss here some of the challenges present in developing capability and accumulating data to support each of these criteria. Developing a pilot model that is capable of being applied to a comprehensive set of use cases, and then verifying those use cases, required significant project management activity.

Premium instrument panels (IPs) contain passenger airbag (PAB) systems that are typically comprised of a stiff plastic substrate and a soft ‘skin’ material which are adhesively bonded. During airbag deployment, the skin tears along the scored edges of the door holding the PAB system, the door opens, and the airbag inflates to protect the occupant. To accurately simulate the PAB deployment dynamics during a crash event all components of the instrument panel and the PAB system, including the skin, must be included in the model. It has been recognized that the material characterization and modeling of the skin tearing behavior are critical for predicting the timing and inflation kinematics of the airbag. Even so, limited data exists in the literature for skin material properties at hot and cold temperatures and at the strain rates created during the airbag deployment.

As fossil fuels dwindle and more electric vehicles enter the market, there is an opportunity to reevaluate the standard brake system. This paper will discuss and compare the differences in brake system sizing between a non-regenerative braking internal combustion engine vehicle and a dedicated battery electric vehicle with regenerative braking. It will use a model derived from component dynamometer testing and vehicle test data of a mid-size production vehicle. The model will be modified for the mass and regenerative braking capabilities of a battery electric vehicle. The contribution of regenerative braking energy will be analyzed and compared to show its impact on component sizing, thermal sizing, and lining life. The detailed design study will calculate the parameters for caliper, rotor design, actuation, etc., that are optimized for 100% regen enabled vehicles.

Understanding process induced fiber orientation distribution of composite body panels using nondestructive techniques is of prime interest. A compression molded sheet molding compound (SMC) panel is a good example of composite panels which are heavily affected by the molding process. Determination of the directionally dependent local coefficient of linear thermal expansion by digital image correlation yields information that is utilized to determine the local fiber misorientation and calculate the local SMC tensile modulus. In our current study, this methodology is utilized to determine the directional CLTE, permitting evaluation of the SMC properties in a multitude of directions not possible in destructive testing techniques. After obtaining the directionally dependent CLTE, a micromechanical approach is utilized to calculate the local SMC tensile modulus and glass fiber misorientation angle.

Finding room to package enough energy at today’s battery energy densities, while preserving performance and configuration requirements is a common problem for electric vehicles. This issue was recently addressed at General Motors by a small team utilizing agile concept development methods, constitutive material model development, and performance simulation tools to create a structural strategy for a family of unique electric light duty trucks. The desire to create a flexible architecture rather than a single vehicle, coupled with an underbody dominant, and rectilinear structural design space precluded any great topological novelty, so a basic principles approach was taken instead. A concept was devised whereby conventional truck frame rails were abandoned in favor of a series of three connected box-like structures along the length of the vehicle. For this to work effectively however, stable shear panels were required as a basic building block.

Several critical factors influence the conventional practice of defining driveline propeller shafts. One of these is the location of the center bearing bracket mounting. This in-turn depends on the frame ladder's crossmember. It has been observed that this dependence results in more number of joints and propeller shafts. “Driveline optimization by mini crossmember” is one of the solutions that offers flexibility in regards to the location of the center bearing bracket. Also this helps in achieving optimization.

Robust engineering is an integral part of the quality initiative, Design For Six Sigma (DFSS), in most companies to enable good designs and products for reliability and durability. Taguchi’s signal-to-noise ratio has been considered as a good performance index for robustness for many years. An alternate approach that is direct and simple for measuring robustness is proposed. In this approach, robustness is measured in terms of an augmented output response and it is a composite index of variation and efficiency of a system. This formulation represents an engineering design intent of a product in a statistical sense, so engineers can understand, communicate, and resonate at ease. Robust formulations are illustrated and discussed with case studies for smaller-the-better, nominal-the-best, and dynamic responses. Confirmation runs of optimization show good agreement of the augmented response with the additive predictive models.

Seat lateral support is often talked about as a design parameter, but usually in terms of psychological perception. There are many difficulties in quantifying lateral support mechanically to the engineering teams: Anthropometric variation causes different people to interact with the seat in different places and at different angles, BPD studies are usually planar and don’t distinguish between horizontal support and vertical resistance to sinking in, most mechanical test systems are typically single-DOF and can’t apply vertical and horizontal loads concurrently, and there is scant literature describing the actual lateral loads of occupants. In this study, we characterize the actual lateral loading on example seating from various sized/shaped occupants according to dynamic pressure distribution. From this information, a six-DOF load and position control test robot (KUKA OccuBot) is used to replicate that pressure distribution.

Thermoplastics find application in many automotive components. Off late, hardware testing is supplemented by analysis using finite element (FE) codes. One of the factors determining the analysis accuracy is the representation of the components with suitable material models. While a uniaxial tensile test on the specimens typically provides engineering stress-strain data, material plasticity models in commercial FE solvers, such as LS-DYNA and ABAQUS, require equivalent plastic strain versus true stress as input. Engineering stress and strain can be converted to the corresponding true stress and true strain using equations based on the constant volume assumption; however, these equations are valid only up to the point of necking.

The automotive industry is continuously striving to reduce vehicle mass by reducing the mass of components including wheel bearings. A typical wheel bearing assembly is mostly steel, including both the wheel and knuckle mounting flanges. Mass optimization of the wheel hub has traditionally been accomplished by reducing the cross-sectional thickness of these components. Recently bearing suppliers have also investigated the use of alternative materials. While bearing component performance is verified through analysis and testing by the supplier, additional effects from system integration and performance over time also need to be comprehended. In a recent new vehicle architecture, the wheel bearing hub flange was reduced to optimize it for low mass. In addition, holes were added for further mass reduction. The design met all the supplier and OEM component level specifications.

Third generation advanced high strength steels (AHSS) that rely on the transformation of austenite to martensite have gained growing interest for implementation into vehicle architectures. Previous studies have identified a dependency of the rate of austenite decomposition on the amount of strain and the associated strain path imposed on the sheet. The rate and amount of austenite transformation can impact the work hardening behavior and tensile properties. However, a deeper understanding of the impact on toughness, and thus crash performance, is not fully developed. In this study, the strain path and strain amounts were systematically controlled to understand the associated correlation to impact toughness in the end application condition (strained and baked). Impact toughness was evaluated using an instrumented Charpy machine with a single sheet v-notch sample configuration.

This study brings to forefront the analysis capability of CFD for the oil-cooling of an Electric-Motor (E-Motor) powering an automobile. With the rapid increase in electrically powered vehicle, there is an increasing need in the CFD modeling community to perform virtual simulations of the E-Motors to determine the viability of the designs and their performance capabilities. The thermal predictions are extremely vital as they have tremendous impact on the design, spacing and sizes of these motors. In this paper, with the Simerics, Inc. software, Simerics-MP+®, a complete three dimensional CFD with conjugate heat transfer CHT model of an Electric Motor, including all the important parts like the windings, rotor and stator laminate, endrings etc. is created. The multiphase Volume of Fluid (VOF) approach is used to model the oil flow inside this motor.

The TOP TIERTM Diesel fuel standard was first established in 2017 to promote better fuel quality in marketplace to address the needs of diesel engines. It provides an automotive recommended fuel specification to be used in tandem with regional diesel fuel specifications or regulations. This fuel standard was developed by TOP TIERTM Diesel Original Equipment Manufacturer (OEM) sponsors made up of representatives of diesel auto and engine manufacturers. This performance specification developed after two years of discussions with various stakeholders such as individual OEMs, members of Truck and Engine Manufacturers Association (EMA), fuel additive companies, as well as fuel producers and marketers. This paper reviews the major aspects of the development of the TOP TIERTM Diesel program including implementation and market adoption challenges.